Is it just my problem?
I cant get Ant+ to work properly in version 6.5.0b
I have to search for Ant+ sensors each time I start
the version new. But even then it is not reliable.
Version 6.5.0Orc6 still works fine with regards to Ant+.
Uli
Quote from: "Uli"
I cant get Ant+ to work properly in version 6.5.0b
I have to search for Ant+ sensors each time I start
the version new. But even then it is not reliable.
Version 6.5.0Orc6 still works fine with regards to Ant+.
Uli
Hi Uli;
I have different ant+ sensors, and all working fine.
There is no changes in ANT management.
Only one app can use simultaneous an ant+ sensor, check that all the ant+ apps are off (including the beta version).
orux
Thank you, Jose,
deleting the beta version and rebooting the phone
solved the problem.
Ant+ works fine on my S5 again.
Uli
Hi,
I have a similar problem. I start ANT+ in 6.5 final in map view, works pefekt but when I switch to TC1 Ant+ signal gets lost and a error message says somthing like " Ant+ is running in a other app and has to be switcht off" OM turns Ant+ off. The rc6 does the same error message when I switch to TC1, but it will not turn Ant+ off OM will reconnect after 20 seconds to Ant+ again and the cadence and speed will be shown. If I use only the heart rate sensor no error at all.
I only run one OM at a time. Hope I made it claer.
Sony xperia active.
Burghard
Quote from: "pfadfinder-outdoor"
I have a similar problem. I start ANT+ in 6.5 final in map view, works pefekt but when I switch to TC1 Ant+ signal gets lost and a error message says somthing like " Ant+ is running in a other app and has to be switcht off" OM turns Ant+ off. The rc6 does the same error message when I switch to TC1, but it will not turn Ant+ off OM will reconnect after 20 seconds to Ant+ again and the cadence and speed will be shown. If I use only the heart rate sensor no error at all.
I only run one OM at a time. Hope I made it claer.
Sony xperia active.
Burghard
Hello,
It should work; sometimes ANT requires a phone restart to work correctly, have you tired?
orux
Hi,
I installt several old betas and rc. I have to go back to 5.5.23rc2 and Ant+ is connecting without error message.
In the OM 6 it is like map view and TC1 are two different Apps. Because when you start Ant+ and switch to TC1 bevor
Ant+ is connected, it will not show the Error, but when you switch to map view it will show the error message.
The 6.5 final connects to Ant+ in map view, but stops Ant+ when you switch to TC1.
The rc6 connects to Ant+ in map view, shows the same error message when you switch to TC1, but will reconnect after 20 sec.
The 5.5.23rc2 connects to Ant+ in map view, when you switch to TC1 it also has to reconnect but without any error message.
However, it is maybe the old Sony Xperia Active and the Old Android-Version 4.0.4
No Problem, for the meantime I will stick with 6.5.0rc2.
regards
Burghard
Quote from: "pfadfinder-outdoor"
I installt several old betas and rc. I have to go back to 5.5.23rc2 and Ant+ is connecting without error message.
In the OM 6 it is like map view and TC1 are two different Apps. Because when you start Ant+ and switch to TC1 bevor
Ant+ is connected, it will not show the Error, but when you switch to map view it will show the error message.
The 6.5 final connects to Ant+ in map view, but stops Ant+ when you switch to TC1.
The rc6 connects to Ant+ in map view, shows the same error message when you switch to TC1, but will reconnect after 20 sec.
The 5.5.23rc2 connects to Ant+ in map view, when you switch to TC1 it also has to reconnect but without any error message.
However, it is maybe the old Sony Xperia Active and the Old Android-Version 4.0.4
No Problem, for the meantime I will stick with 6.5.0rc2.
regards
Burghard
Hello,
yes, the app disconnects and reconnects when you leave the map viewer, if you are not logging a track.
but the reconnection should be instantaneous. It works with my ant+ sensors.
may be the problem is with the sensor.
orux
Hi,
thank you for your time. It is working again. :D
Deinstall all OM, saved all maps and routes, clean new Install.
To much beta testing :?:
Thanks